Image on left is from 4 days ago, but the pimple was slowly forming over around 2 weeks.

The goop was sticky, not oily. Earphones are Panasonic RP-TCM130.

I was not able to find an explanation.
Something to increase cable lifespan, lubrication, rubber disintegrating, sweat and earwax that somehow got into the cable, dielectric grease, SCP-1407, no clear answer.

At first I thought the wires just somehow twisted. Nope.

  • bbuez@lemmy.world
    link
    fedilink
    arrow-up
    29
    ·
    7 days ago

    Makes me think of that shitty grippy rubber material on cheap mice that becomes gooey with time. I would treat those as euclid until further testing

  • nezbyte@lemmy.world
    link
    fedilink
    arrow-up
    11
    ·
    7 days ago

    Some sort of chemical reaction. My best guess would be a drop of CA glue that degraded the material over time.

  • UsernameHere@lemmy.world
    link
    fedilink
    arrow-up
    16
    arrow-down
    1
    ·
    7 days ago

    High resistance in a wire inside the sheath would generate more heat at that point, causing the plastic sheath to melt/bubble. So if the wire inside the sheath got damaged, pinched or some of the strands of wire were broken.

      • Orbituary@lemmy.world
        link
        fedilink
        English
        arrow-up
        12
        arrow-down
        2
        ·
        7 days ago

        You would be incorrect. If the power source shorts, it would heat the wires sufficiently.

        • fuckwit_mcbumcrumble@lemmy.dbzer0.com
          link
          fedilink
          English
          arrow-up
          7
          arrow-down
          1
          ·
          6 days ago

          And how much power do you think the DAC in a phone is going to output?

          The built in DAC in a phone can barely drive my headphones, let alone melt a silicone cable. They typically output less than a watt. On a good day. Rubbers melting point is 365c and 1 watt isn’t gonna do that.

          • u/lukmly013 💾 (lemmy.sdf.org)@lemmy.sdf.orgOP
            link
            fedilink
            English
            arrow-up
            3
            ·
            6 days ago

            They typically output less than a watt.

            Sounds optimistic. Checking a few USB to 3.5mm dongles, they seem to be around 25mW max at 32Ohms. Not sure how much that would change with short circuit, but I guess not much more.

          • UsernameHere@lemmy.world
            link
            fedilink
            arrow-up
            2
            arrow-down
            3
            ·
            6 days ago

            Have you verified the specs on OPs headphones?

            Maybe I missed it but I don’t see where OP said this happened while connected to a phone.

            • fuckwit_mcbumcrumble@lemmy.dbzer0.com
              link
              fedilink
              English
              arrow-up
              3
              ·
              6 days ago

              They’re earbuds. You’re going to using them with a phone, maybe a laptop, or even in a pinch maybe a desktop. None of those output enough power to melt through a rubber cable without severely destroying themselves and never working again. OP would be posting “my phone exploded and I’m deaf now” not about the cable having a pimple.

              Even my dedicated amp, a Shiit Magni outputs 6 watts with both channels combined, and ain’t nobody connecting shitty earbuds to an amp. The rest of the cable is going to sink away the heat from 6 watts before the rubber could get hot enough to melt.

  • snooggums@midwest.social
    link
    fedilink
    English
    arrow-up
    3
    ·
    7 days ago

    I am so intruiged by the fact that the mass of good accumulated at the one spot. The mystery of what pressures were at play for it to flow to that one spot.

  • VelvetStorm@lemmy.world
    link
    fedilink
    arrow-up
    3
    ·
    6 days ago

    Sir, you are to remain in your present location until MFT Psi-8 makes contact. Any and all resistance will be met with force!